The daily maintenance of the hydraulic lifting platform in normal use is essential but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.Trento,Power unit adjustment, whether it is a scissor lift platform or a rail-type lift, is controlled by the power unit and the oil cylinder. The power unit is equipped with four outlet holes during production, which can be adjusted in size to increase or decrease the oil cylinder. Hydraulic oil flow, we can adjust the motor speed or the electro-hydraulic proportional valve to adjust the hydraulic oil flow; what factors will affect the lifting speed of the hydraulic lift oil pipe, the longer the hydraulic oil pipe, the longer the rise time. Therefore during installation, the length of the oil pipe should be reduced as much as possible within the allowable range of the design; on the basis of adjusting the power unit, the size of the oil pipeline can also be adjusted, and on the premise of ensuring that the equipment meets the normal requirements and safety, municipal construction,TrentoGuide rail chain elevator, and decoration of hotels and hotels, with reliable quality and perfect performance.Izyum,The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather,TrentoHydraulic lifting cargo elevator, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, the lift also has a lot of safety equipment.If the hydraulic valve is damaged, its effectiveness should be maintained. If it is damaged, it can be replaced in time.System: explosion-proof electronic control system, P IC system.Quality inspection report,Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose,TrentoWhere can I sell elevators for goods, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector, and the cost is not high. It is both affordable and safe, and can effectively prevent electric shock.Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.

Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.Latest consultation,Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.The series of standards related to mobile elevators. This series of standards is based on the Ministry of Construction's Jianbiao No. document and [] No. document of the Ministry of Construction's product standards. Standards, this series of standards refers to the American ANSIA- 'boom-type elevating work platform' standard and the American ANSI-A- 'self-propelled aerial work platform' standard, and also refers to relevant European industry standards. The standard was reviewed by relevant Chinese departments on January . The review opinion is: the series of standards for aerial work platforms are comprehensive in content, strong in support, and sufficient in basis, reflecting the advanced nature and scientific nature of the standards, and the main performance indicators have reached the international advanced level. The standard was published on /.Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.Trento,Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls rollers, Turntable steering, tilting, telescopic), with various methods (separate, linkage, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting, large load capacity, etc. effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, scratches, small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.