For example, the price of tons of goods = tons = the result example: the price excluding tax of ton of goods = a ton = ~ the total weight of the known coil weight and price = the coil weight price, the thickness of stainless steel plate & Chi; Width & Chi; Long & Chi; e.g. & Chi; Χ Χ = kg stainless steel plate weight per square meter (kg) calculation formula: specific gravity thickness (mm) width (mm) length (m) stainless steel weight per meter (kg) stainless steel pipe calculation formula: diameter (mm) diameter (mm) (correct calculation of the price difference between burr and trimming of nickel stainless steel . chromium stainless steel) in the market, the price difference between burr and trimming of stainless steel is usually set at a fixed price. For example, it is generally considered in the market that the price difference between burr and trimming of is yuan tons and that of is yuan tons. In fact, this method is not scientific. In fact, the price difference between burr and trimming of stainless steel is different The correct calculation should be like this.Raw materials -- strip splitting -- welded pipe making -- heat treatment -- Correction -- straightening -- end repair -- pickling -- Hydrostatic Test -- Inspection (spray printing) - packaging -- delivery (warehousing) (pipes for welded pipe industrial piping).Radovish,The length of tungsten electrode protruding from the gas nozzle is preferably ~ mm. In places with poor shielding such as fillet welding, it is ~ mm, and in places with deep groove, it is ~ mm. The distance from the nozzle to the working is generally no more than mm.Vickers hardness stainless steel pipe Vickers hardness test is also an indentation test,Radovish310S seamless stainless steel pipe, which can be used to determine the hardness of very thin metal materials and surface layers. It has the main advantages of Brinell and Rockwell methods and overcomes their basic disadvantages, but it is not as simple as Rockwell method. Vickers method is rarely used in steel pipe standards.Karagandy, which have good processing properties. Deep drawing, bending, crimping and welding can be carried out without preheating. Crl does not require preheating before cold deformation, but preheating is required before welding. crlcr is mainly used to make corrosion-resistant structural parts such as steam turbine blades, while crcr is mainly used to make surgical and wear-resistant parts of medical instruments; crl can be used as corrosion-resistant bearings and tools.Stainless steel pipe is safe, reliable, hygienic, environmentally friendly,Radovish304 stainless steel welded pipe, economical and applicable. The successful development of pipeline and new reliable, simple and convenient connection makes it have more irreplaceable advantages of other pipes. It will be used more and more in engineering, and the use will be more and more popular. It has a good prospect.Crimping: during crimping, the convex part of the pipe fitting is placed in the concave groove of the die and the jaw is perpendicular to the pipe axis.

The specific steps of continuous casting billet process of stainless steel pipe fittings are as follows: according to different steel grades, which can improve the yield of %, save energy and shorten the production cycle so as to improve the yield of molten steel.　　SPHDSPHD—& mdash; Hot rolled steel plate and strip for stamping.The main way to prevent stress corrosion of austenitic stainless steel is to add SI ~ % and keep the content of N below .% from smelting. In addition, Sb the content of impurities such as P, Bi and as should be reduced as much as possible. In addition, A-F dual phase steel can be selected, which does not correspond to stress corrosion in Cl - and oh - media. The initial micro crack will not continue to expand after encountering ferrite phase, and the ferrite content should be about % .knowledge, chemical composition and application pressure, and the commodities of corresponding grades shall be selected to ensure the weld metal structure and machine function.Stainless steel pipe cost = actual thickness divided by thickness adjustment price + freight + processing fee. Coil price is switched to flat plate price = coil price, actual thickness adjustment + leveling fee . Flat plate price is switched to coil price = plate price, thickness adjustment - leveling fee . Coil length = coil net weight . Coil width. Actual thickness including tax price algorithm = total weight of goods ( represents points, is points) the responsibility of the calender is that the annealed steel strip is blackened the furnace liner is perforated, and ammonia leakage will cause rust. . The responsibility of the steel plant is that the peeling and trachoma of the steel strip will cause rust. Substandard materials will cause rust. the responsibility of the calender is that the annealed steel strip is blackened, the furnace liner is perforated, and ammonia leakage will cause rust. . The responsibility of the pipe manufacturer: the welds in the pipe manufacturer are polished rough, which will cause rust.

Add a small amount of sulfur and phosphorus to make it easier to cut.Honest management,Flux coated welding wire (self shielded welding wire) shall be used for backing TIG welding.　　SPHDSPHD—& mdash; Hot rolled steel plate and strip for stamping.Stabilization treatment. Generally, it is used for - steel containing Ti and Nb in the solid solution treatment line. After the solid treatment, the steel is heated to ~ ℃ for heat preservation and air cooling. At this time, the carbides of Cr are completely dissolved, while the carbides of titanium removal are not completely dissolved, and they are fully precipitated during the cooling process, so that it is impossible for the carbon to form chromium carbides again. Professional L stainless steel pipe, s stainless steel pipe and L stainless steel pipe ensure the quality, Guarantee service. Guarantee quality. Your satisfaction is our pursuit! Welcome to inquire. Therefore, intergranular corrosion is effectively eliminated.Radovish,When hoisting stainless steel pipes, public slings, such as hoisting belt and public collet number, shall be used. It is strictly prohibited to use steel wire rope to avoid scratching the surface; and when hoisting and placing, it shall prevent scratching caused by impact and collision. If there are surface scratches, electric arc traces and surface purification in the process of transportation, storage and processing, it must be completely cleaned, and then polished Polishing with optical sheet or metallographic sandpaper.After fine tuning the molten steel temperature in the argon blowing station, it is lifted to the ladle rotary table for continuous casting.When using this process, the following key points should be paid attention to: during the welding process, the correct included angle between the welding handle, and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature,Radovish420F stainless steel plate, change the included angle between the welding handle and weldment, change the welding speed, etc. to change the molten pool temperature, so as to ensure Beautiful weld formation (uniform width, no concave, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating, so as to facilitate the observation of molten pool and penetration; when filling the welding wire, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding, the welding wire shall be regularly sent and taken out, and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.