Ensure that the service time will be extended when it is used. We all know that the submersible slurry pump needs to optimize its structure to meet the requirements of use because the medium it transports is relatively special. The structure has been optimized to　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.Azad shar,　　If there is a fault, it is inconvenient to repair.　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, and the submersible slurry pump can supplement this part of the blank work point.Neunkirchen,　　Stop, then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, and say that the nut is loose　　Ordinary vertical motor can be used without waterproof, while the motor shaft and pump shaft of submersible slurry pump are coaxial so the motor must be waterproof and sealed, and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product, and the submersible slurry pump is a newly developed product according to the market demand　　The use of water pumps for agricultural drainage and irrigation can improve the ability of agriculture to resist natural disasters, increase production and ensure income, and provide material conditions for agricultural mechanization and water conservancy.

　　With water, you can start working.　　 Determine the head h. After the flow is determined, determine the inlet and outlet pipe diameters of the pump, complete the layout of the whole pipeline, and determine the head. In the actual selection,Azad sharCorrosive pipeline pump, the resistance coefficient of the pipeline is often too large. In addition,Azad sharSubmersible non clogging slurry pump, when selecting the pump model a head margin is added, resulting in　　Friction resistance due to bearing and packing; Friction between impeller and water during rotation; The vortex of water flow in the pump, gap reflux, inlet and outlet impact and other reasons. A part of the power must be consumed, so it is impossible for the water pump to completely change the power input by the power machine into effective power, in which the constant active powerWhich one is better, bearing puller (commonly known as triangle puller), magnetic dial indicator, outside micrometer, caliper, feeler gauge, square ruler, copper bar screwdriver with handle, hammer, V-shaped irons of the same specification, clean kerosene, oil basin, cotton yarn, etc.　　 Next, the water seal, lock ring and other parts need to be installed.　　 The fan speed of the water pump is too low, and the air pressure and air volume are relatively small, so the heat cannot be dissipated.

　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.Standard requirements　　Circumference. In the application of slurry pump, we must pay attention to reasonable design,Azad sharZD slurry pump, correct calculation and appropriate type selection, which are very important. In addition to the main wheel, a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particles　　 WQ series submersible sewage pump has fixed and mobile devices, as shown in the figure. When the fixed driving device is selected, the chain cable shall be separately threaded into (away from the pump outlet, and its connecting line shall be parallel to the axis of the pump outlet) two lifting eye screws or lifting plates to lift the electric pump up and down,　　Superior, complete protection s, reasonable structure, the water pump will automatically start to supplement the pipe network pressure.Azad shar,　　Water pump is a kind of machinery that pumps energy liquid. It is a machine that converts the mechanical energy of the prime mover into the potential energy of the pumped liquid. Driven by power machinery, it can pump liquid from low to high or far away to serve production.　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time　　Under the action of auxiliary devices, it can transport the slurry, and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal use