Solution treatment. The main purpose of water quenching after heating the steel to ~ ℃ is to dissolve the carbide in austenite and keep this state to room temperature, so that the corrosion resistance of the steel will be greatly improved. As mentioned above, in order to prevent intergranular corrosion, solid solution treatment is usually used to dissolve CrC in austenite and then cool rapidly. Air cooling can be adopted for parts, and water cooling is generally adopted.The numbering rules adopt element symbols; Pinyin,New Gorica302 stainless steel pipe,New GoricaStainless steel belt, open hearth steel: p; Boiling steel: F; Killed steel: B; Class a steel: a; T: special GCr: ball.New Gorica,Long term professional L stainless steel pipe, s stainless steel pipe and L stainless steel pipe. Therefore, the specification of a group of slightly larger formed pipes used in the production of pipe dies is about -.Welding, high frequency preheating plus three torch argon arc welding, the weld quality is equivalent to the conventional argon arc welding and plasma welding, the welding operation is complex, and the whole welding is easy to complete automation. This combination is easy to connect with the existing high-frequency welding equipment, with low investment cost and good benefit.Bir el Ater,Therefore, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry.Stainless steel pipe is safe, hygienic, economical and applicable. The successful development of pipeline and new reliable, simple and convenient connection makes it have more irreplaceable advantages of other pipes. It will be used more and more in engineering, and the use will be more and more popular. It has a good prospect.The specific steps of continuous casting billet process of stainless steel pipe fittings are as follows: according to different steel grades, the vibration process of mold is matched with protective slag, which can improve the yield of %, save energy and shorten the production cycle, so as to improve the yield of molten steel.

Crimping: during crimping, the convex part of the pipe fitting is placed in the concave groove of the die, and the jaw is perpendicular to the pipe axis.The national standard thickness of stainless steel pipe mainly depends on the thickness of raw materials and processing technology. The thickness of welded pipe is basically the same as that of raw materials. For seamless pipe, it is slightly thinner than that of raw materials. At present, the stainless steel pipe industry is dominated by large negative difference, mainly for the consideration of cost saving, thickness. It provides all kinds of stainless steel plates, stainless steel coils, stainless steel belts, stainless steel pipes for individuals and enterprises all over the country for a long time, on-site settlement and honest operation. There are offices all over the country for long-term cooperation. Generally, there will be . ~ .Combined steel and spring steel, such as CrMnTi simn, (C content is expressed in ten thousandths).packing,Solution treatment. The main purpose of water quenching after heating the steel to ~ ℃ is to dissolve the carbide in austenite and keep this state to room temperature, so that the corrosion resistance of the steel will be greatly improved. As mentioned above, in order to prevent intergranular corrosion solid solution treatment is usually used to dissolve CrC in austenite and then cool rapidly. Air cooling can be adopted for parts, and water cooling is generally adopted.The scale pretreatment of stainless steel pipe makes the scale loose, and then acid pickling is carried out for easy removal. The pretreatment can be divided into the following: alkaline salt melting treatment method. The alkaline melt contains % hydroxide and % salt. The proportion of the two in the molten salt shall be strict, so that the molten salt has strong oxidizing power, low melting point and small viscosity. Only the sodium halo shall be analyzed in the production process, and the content shall not be less than % (wt) It is treated in a salt bath furnace at ~ ℃ for minutes for ferritic stainless steel and minutes for austenitic stainless steel. Similarly, iron oxides and spinels can also be oxidized by salt to become loose ferric oxide, which is easy to be removed during acid pickling. Due to the action of high temperature, some of the formed oxides peel off and sink to the furnace bottom in the form of sediment. Alkaline salt melting pretreatment Process flow: steam degreasing → preheating ( ~ ℃, time ~ min) ↠ molten salt treatment & rarr; water quenching & rarr; hot water washing. Molten salt treatment is not suitable for assemblies with weld gap or crimping. When the parts are taken out of the molten salt furnace, a stream of alkali and salt mist will be splashed during water quenching, so deep well anti splash water quenching tank shall be used during water quenching. During water quenching,New GoricaStainless steel pipe 201, firstly lift the parts basket into the tank, stop above the horizontal plane, close the tank cover, and then lower the parts basket into the water, Professional L stainless steel pipe, s stainless steel pipe and L stainless steel pipe are stable safe, reliable and maintenance free. The technical level has reached the domestic level and the international advanced level of similar products until submerged.When installing and welding the fixed port of stainless steel pipe, it is difficult to vent on the inner side, and some sides are easy to be blocked. In this case, water-soluble paper + blocking plate can be used for blocking. That is, the easy to vent and good side can be blocked with blocking plate, the difficult to vent and bad blocking plate side can be blocked with water-soluble paper, and the weld on the outer side can be blocked with adhesive tape (see Table ) .

Stress relief treatment. Stress relief treatment is a heat treatment process to eliminate the residual stress of steel after cold working or welding. It is generally heated to ~ ℃ for tempering. For steels without stabilizing elements Ti and Nb, so as to avoid intergranular corrosion caused by chromium carbide precipitation. For cold worked and welded parts of ultra-low carbon and stainless steel containing Ti and Nb, they need to be heated at ~ ℃ and then cooled slowly to eliminate stress (the upper limit temperature is taken for eliminating welding stress), which can reduce the tendency of intergranular corrosion and improve the stress corrosion resistance of steel.Analysis project,The welding of stainless steel pipe is usually composed of backing welding, which is not only related to the quality of engineeringAs we all know, stainless steel pipe has a strong ability of atmospheric oxidation and is not easy to rust under normal circumstances, & ldquo; Stainless steel pipe & rdquo; Hence the name of. But what I want to tell you today is that stainless steel pipes will also rust. I believe many friends will be surprised! I believe there are many people who don't know how to explain to customers! Next, let's popularize science!There shall be a special storage rack. The storage rack shall be a wooden or painted carbon steel support or padded with rubber pad to isolate it from carbon steel and other metal materials. During storage, the storage position shall be convenient for lifting and absolutely isolated from other data storage areas. Protective measures shall be taken to avoid purification, collision with other components, purification and damage of iron metal.New Gorica,Austenitic stainless steel. It contains more than % chromium, about % nickel and a small amount of molybdenum, titanium, nitrogen and other elements. Good comprehensive performance and resistance to corrosion of various media.For more than years, architects have been using stainless steel to build cost-effective buildings. Many existing buildings fully illustrate the correctness of this choice. Some are very ornamental such as the Chrysler Building in New York City. However, in many other applications, the role of stainless steel is not so eye-catching, but in the aesthetics and performance of buildings For example because stainless steel has more wear resistance and pressure resistance than other metal materials of the same thickness, it is the preferred material for designers when building sidewalks in places with large population flow.Stainless steel pipe, which was produced and used in China at the end of the s, is a new family emerging in the field of pipe materials. It has been widely used in building water supply and direct drinking water pipelines.