building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.　　Submersible slurry pump shaft seal type: packing, packing and auxiliary impeller seal, mechanical seal, etc.Brondslev,　　The equipment of this series of sewage pumps can be fixed or mobile. When the fixed active equipment is selected, the chain cable shall be separately threaded into (against the pump outlet, and its connection shall be parallel to the pump outlet) two eyebolts or lifting plates to lift the electric pump up and down. Evenly and slowly along the guide rail　　 There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the mainAndoany,　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.　　 Next, the water seal, lock ring and other parts need to be installed.　　 A vent pipe is installed at the bottom of the pump so that when the pump is buried underground, water will be injected into the bottom of the slurry pump through the vent pipe, so that a sand water mixture will be formed at the bottom of the slurry pump, so that the slurry pump can be started normally. The advantage of this approach is that even if

　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. The submersible slurry pump is developed to adapt to increasingly complex working conditions and facilitate the use of users. Its use mode is more　　 The fire control cabinet has fault alarm . When a single fire pump is working, it is not easy to be found in time in case of insufficient water source,BrondslevTwo stage slurry pump, power circuit failure, the alarm of the control cabinet can remind each　　Carbon resulting in damage to the fire pump. Using the fire control cabinet, building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.How much does it cost?,　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.　　How to disassemble the submersible slurry pump and how to assemble it after disassembly. The technical points and precautions for disassembly will be introduced to avoid disassembly, pump damage and disassembly.　　Water pump After understanding the cause of insufficient liquid supply, we can solve the problem: First we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.

　　; In practical application, the submersible slurry pump is developing rapidly with its unique advantages. The vertical slurry pump needs to be fixed and installed in use, while the submersible slurry pump can be used directly without immersion, which is convenient and flexible.total cost,　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.　　Fire pump control cabinet generally has two control modes: one is fire hydrant control, and the other is spray pump control. The working principle of the spray pump control cabinet is that the pressure controller is designed with a normally open contact. When the pressure relay acts due to the pressure difference, the control circuit moves the main circuit　　Water pump After understanding the cause of insufficient liquid supply, we can solve the problem: First, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.Brondslev,BrondslevWater well pipeline pump,　　Submersible slurry pump In addition, it must be used continuously during transportation. If there is an interval in the middle,BrondslevVertical centrifugal slurry pump, it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped.　　 selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.　　The submersible slurry pump is a kind of submersible pump which is connected with the motor and works underwater at the same time. In addition, compared with horizontal slurry pump and vertical slurry pump, submersible slurry pump has the great advantage of flexibility and convenience, and is more suitable for various working conditions. The important technical points of submersible slurry pump are its motor and