The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.Advantages of using I-beam: reduce maintenance cost, reduce downtime, improve equipment operation rate, reduce wear, reduce equipment capacity and increase power consumptionKicevo,Precautions for galvanized pipe storageMain uses: as a finished material, flat steel can be used to make hoop iron, tools and mechanical parts, and used as building frame structural parts and escalators in buildings. Flat steel is divided into two types according to its shape: plane spring flat steel and single-sided double groove spring flat steel. Hot rolled spring flat steel is mainly used to manufacture leaf springs for automobiles, tractors, railway transportation and other machinery.Ilkutsk→ under the same section load, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure.The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Heating surface tubes for low and medium pressure boilers (working pressure is generally not greater than MPA and working temperature is below ℃);

Pass designAccording to the historical records of the recent four years, the zinc price in the first quarter was generally higher than that in the whole year, and generally entered a wave of upward trend in the first quarter. However, zinc prices continued to decline in the first quarter of , and showed a trend of accelerating the decline day by day. There are two key reasons for the beginning of this year. First,KicevoWholesale of No. 16 I-beam, the vicious change of the real estate industry has led to a rapid decline in the growth rate of China&#;s consumption of galvanized pipe and seamless steel pipe, and even a contraction month on month; Secondly, the blind expansion of galvanized pipe factory confused the sense of rhythm of supply and demand balance.Because alloy pipe is a very unique pipe fitting, we must use appropriate methods to carry out installation in the case of installation, so as to ensure the performance index of the data. Generally, when installing alloy pipes, we will use some flanges and elbows to fix them, so as to ensure that the raw materials can be fixed very well. Therefore, when we carry out use, we must ensure the quality of flanges and elbows, so as to ensure the actual effect of alloy pipe assembly. If there are instrument panel components that must be assembled on the pipeline, they must be installed together.Service first,All the cracks occur at -mm away from the edge below the alloy pipe, and the macroeconomic orientation is vertical to the cold rolling orientation, bearing performance and service life. This paper systematically introduces the development of high quality cold drawn bearing steel pipe and its application in bearing. Precision cold rolling of small and medium-sized bearing sleeves with bearing steel pipes can greatly improve material utilization, bearing performance and service life. This paper systematically introduces the service life of high quality cold drawn bearings.Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.

Some applications of I-beam:Design brand, Hot push hole diameter. More sensitive applications and facilities of such methods require simplicity, low cost easy maintenance, durable economic development and convenient product specification transformation. For example, the production of large diameter must be grooved pipe, elbow and similar products. You only need to add some spare parts. The expansion method of hot push can be used to process and manufacture large-diameter, thick wall and thin alloy steel pipes, and can not exceed the working capacity of thick wall pipes of machinery and equipment.The production methods of seamless pipe are roughly divided into cross rolling method and extrusion method. The cross rolling method is to drill the tube with a cross roll, and then extend it to the rolling mill. This method has fast production speed, but has high requirements for the workability of the blank. It is mainly suitable for the production of carbon steel and low alloy steel pipes. The extrusion law is to pierce the blank or ingot with a punch,Kicevo15CrMo seamless pipe manufacturer, and then squeeze it with a steel pipe with an extruder. The efficiency of this method is lower than that of cross rolling method. It is suitable for producing high-strength alloy steel pipe. The billet or ingot must be heated before cross rolling method and extrusion method. The produced steel pipe is called thermal correlation. Steel pipes produced by hot working can sometimes be cold worked as needed. There are two methods of cold working. One is cold drawing. In other words pull the pipe to the pipe and tilt it to make the steel pipe gradually thinner and longer. Another method is cold rolling. The method of applying the hot smoke invented by brother to cold processing. The cold working of seamless pipe can improve the dimensional accuracy and finishing of steel pipe, and improve the mechanical properties of materials.C-section steel has uniform zinc layer, smooth surface, no zinc scar, no zinc leakage and high dimensional accuracy. All surfaces are wrapped by zinc layer, and the zinc content on the surface is usually -g /? It has long service life, corrosion resistance and durability. It is a kind of stronger protection.Kicevo,Dry processing technology: after passivation treatment, or drying treatment or air drying can be selected.Whether I-section steel is ordinary or light because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members.Because all parts of I-beam are arranged at right angles, I-beam has the advantages of strong bending resistance, simple construction,KicevoTable of several inches corresponding to welded pipe, cost saving and light structural weight in all directions, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel, and the end of the flange is at a right angle, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web, and the flange width is larger than that of ordinary I-beam with the same height of web