The flange of H-beam is of equal thickness including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small) a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.What are the uses of I-beam?Jerino,Special shaped pipe: square pipe, rectangular pipe, cap pipe, steel pipe for hollow rubber steel doors and windows welded by general carbon structure steel and Mn steel strip, mainly used as agricultural machinery components, steel windows and doors, etc.Generally, the process of pickling and passivation will be carried out for alloy pipes, but the alloy pipes after pickling and passivation are very easy to rust. Therefore, the way to find a solution to wiredrawing corrosion is 'grinding and polishing'. Due to grinding and polishing, there is no harm to carry out hot galvanizing in the middle and later stage.Mizdah, H-section steel is an economic section steel with better mechanical properties than I-section steel. It is named because its section shape is the same as the English letter 'H'. The flange of hot rolled H-beam is wider than that of I-beam, with large lateral stiffness and strong bending resistance. Under the same specification, H-beam is lighter than I-beam.Metallization: refers to the process of penetrating metal atoms into the surface layer of alloy steel pipe. It is to alloy the surface layer of steel so that the workpiece surface has the characteristics of some alloy steel. Aluminizing, chromizing, boronizing, siliconizing and so on are commonly used in production.Whether I-section steel is ordinary or light because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members.

Advantages of using I-beam: reduce maintenance cost, reduce downtime, improve equipment operation rate, reduce wear, reduce equipment capacity and increase power consumptionGalvanized pipe is often seen in our daily life, especially in some construction sites. This product has the advantage of durability when used. It also has the characteristics of surface gloss, uniform zinc layer and no missing plating. Moreover, the cost of hot-dip galvanizing for rust prevention is lower than that of other paint coatings. In addition, strong adhesion, breaking the clean Legion and strong corrosion resistance. Even if it is used in some places where the environment is not good, its service life is also very long, and it also has the characteristics of corrosion resistance. The standard anti rust thickness of hot-dip galvanizing can be maintained for more than years without repair. This is used in some suburban environments. However, in urban or offshore areas, standard urban or offshore areas can be maintained for years without repair. The products produced by our company must meet these requirements. Friends who need to order can call us directly.I-beam, also known as universal beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.Good quality,H-beam is a widely used profile in steel structure buildings. It is different from I-beam. The first is the flange, and the second is that the inner surface of the flange has no inclination, and the upper and lower surfaces are parallel. The section characteristics of H-beam are obviously better than those of traditional I-beam, channel steel and angle steel.Dry processing technology: after passivation treatment parts shall be dried with air compression or hot gas, or drying treatment or air drying can be selected.The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.

After the passivation treatment of alloy pipe, it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution, ~ times of water cleaning, and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃, and the solution time is min. Then dry.average method, Special rolling method. When it is difficult to roll the required I-beam by the usual rolling method for some reason, the special rolling method can be used to make full use of the skills of uneven deformation and pass design. For example,Jerino15CrMo seamless alloy pipe,JerinoHow much is 50 galvanized pipe per meter, when the billet section is narrow and wide I-beam is required to be rolled, the wave rolling method can be used; for example, when the billet is wide and small I-beam is required to be rolled, the negative rolling method can be used Spread rolling, etc.Steel transfers heat excellently; Can withstand high temperature; Strong and strong materials; Probably a long time ago. In addition, there is the low cost of metal.The working principle of flat steel finishing machine in I-beam production process is to pre level and finally level the cold flat steel with two groups of leveling wheel sets staggered up and down in the thickness direction; A pair of finishing wheels arranged relatively are used to extrude the width direction, so that the width is compressed to achieve the expected parameters, and the compression amount is adjustable; Straighten the width with staggered straightening wheels.Jerino,Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.Welded steel pipes need to be processed through various processes before application. The heat treatment of welded steel pipes is a very important link in the processing of welded steel pipes. Hot working is a metal hot working process in which metal materials are heated, insulated and cooled in a certain medium, and their metal properties are controlled by changing the metallographic structure on the surface or inside of the material. During the heating and cooling process of structural welded steel pipe workpiece, the temperature difference will be formed,JerinoHow much is a ton of welded pipe, which will lead to uneven volume expansion and contraction and produce stress, that is, thermal stress.C - section steel is reliable and stable in stress, can be accurately positioned, it has good versatility and combination, and has a variety of C-section steel and size selection to ensure its flexibility