Function of I-beam: where is I-beam mainly used?The system is mainly composed of control box, finishing roller, pre leveling unit finishing unit and straightening unit.Delirium,A major defect is its instability to the corrosion process, which can not resist all factors. Producers need a solution that can solve the corrosion problem. The decision has been found. They become a galvanized steel pipe.Greatly reduce the environmental pollution caused by abrasion, damage and blanking,Delirium50 galvanized pipe is a few inches of pipe, and increase the labor cost of material cleaningLondon, Special rolling method. When it is difficult to roll the required I-beam by the usual rolling method for some reason, the special rolling method can be used to make full use of the skills of uneven deformation and pass design. For example, when the billet section is narrow and wide I-beam is required to be rolled, the wave rolling method can be used; for example, when the billet is wide and small I-beam is required to be rolled, the negative rolling method can be used Spread rolling, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane,Delirium45# precision seamless pipe, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.

The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.In our daily life and work, we can often see a lot of steel products. At the same time, among many steel products, the figure of galvanized pipe is particularly prominent. This is because this kind of pipe will be applied to many engineering construction we often see in our life. There are also countless products processed with this kind of pipe. For example, in the field of mechanical equipment processing we often see, the application of galvanized pipe is more frequent. Let&#;s discuss the application scope of this kind of pipe today.The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore,DeliriumHow much is a 4-point galvanized pipe, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm,What should we pay attention to in the production of alloy pipeThe crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.The import and export order of I-beam is generally based on the specifications required in use after determining the corresponding carbon structure steel (or low alloy steel) steel grade. Except for the specification number, I-beam has no specific composition and performance series.

The utility model has the advantages that the axial force of the roll is small, the axial movement is small, and the working slope is not required,Good quality,The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.Galvanized pipe is a layer of galvanized ordinary steel. This is a layer and is a great anti-corrosion protection.Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.Delirium,Application scope of alloy pipeI-beam: national standard * what is the wall thickness of I-beamMixed Scabs are distributed periodically, and the situation after casting and rolling is significant through edge flame peeling crack inspection or billet scratch flame removal.