Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment it will not affect the detection results. Therefore,Hau Kip DasCarbon steel explosion-proof pipeline pump, many pumps often have better measurement results when in use.　　 Next, the water seal, lock ring and other parts need to be installed.Hau Kip Das, but there are several possible reasons: the water inlet is blocked; The bottom valve is not deep enough underwater; The running speed of the water pump is not enough; leaf　　It is not correct that it has no effect on us.Safita,　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage　　 confirm whether the pressure capacity of the pipeline meets the requirements, and conduct hydrostatic test if necessary.　　The high-pressure water flows to the space occupied by the original bubble at a very high speed forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressure

　　Pressure. Therefore, a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.　　 If the deep well pump is not used continuously after running in the well, it should be started up once a week and run for - minutes to prevent the electric pump from being started due to corrosion.　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.technical service,　　; In practical application, the submersible slurry pump is developing rapidly with its unique advantages. The vertical slurry pump needs to be fixed and installed in use, which is convenient and flexible.　　No matter what type of slurry pump you need, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　Therefore, when the pump temperature is too high, so as to find out the root cause of the excessive temperature of the equipment in time and then take relative measures to effectively solve it.

　　 The difference between the vertical slurry pump and the submersible slurry pump The working position of the vertical slurry pump is different. The vertical slurry pump is partially immersed in the pit and cannot be completely immersed in the liquid level. The submersible slurry pump can be completely immersed (including the motor part) below the liquid level; Use of motor for vertical slurry pumpHigh value,　　Submersible slurry pump In addition, the sewage pump is usually driven by a motor, which also requires some time og quantity when switching on and off, so in fact,Hau Kip DasDrilling fluid slurry pump, it can be adjusted to a certain extent during use. The submersible slurry pump needs to use a line when in use　　 There are several reasons for the severe vibration of the pump body: the phenomenon of unbalanced rotation of the electric rotor.　　The disc friction loss of the slurry pump impeller will decrease with the decrease of the impeller diameter, so that the pump efficiency of most low specific speed pumps will improve slightly after the impeller is cut. After cutting, keep the blades overlapped to a certain extent,Hau Kip DasSubmersible pump can pump sewage, and the degree of blade overlap will decrease with the addition of specific speedHau Kip Das,　　 Cutting blades can be selected to cut some large block solid substances into pieces during use, so that blockage can be avoided during reuse.　　Circumference. In the application of slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection, which are very important. In addition to the main wheel, a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particles　　For example, in the market, for example, the sweeping pump, some of which have a depth of more than meters, it is not suitable to use a vertical slurry pump under such a working condition, but it is extremely easy to use a submersible slurry pump.