Production process of stainless steel welded pipe: raw material - strip - welded pipe - end repair - polishing - Inspection (spray printing) - Packaging - shipment (warehousing) (decorative welded pipe).Low temperature embrittlement of stainless steel pipe --- in low temperature environment, the deformation energy is small. In low temperature environment, the phenomenon of reduced elongation and area shrinkage is called low temperature embrittlement. It is mostly produced on the body centered cubic structure of ferrite series.Jesenice, thin strip, roll strip, calendering strip and other strips can be cut with a thickness of . to mm (Note: stainless steel calendering strips of various thickness and width can be produced according to the needs of customers)Standard classification - classification: national standard GB industry standard Yb local standard enterprise standard qcb- classification: product standard packaging standard basic standard - standard level (divided into three levels): y level: international advanced level I level: international general level H level: domestic advanced level - national standard: stainless steel bar (level I) gb- stainless welding disc Park (level H)Chachoengsao,Assembly: the sealing ring shall be correctly installed in the U-groove of the pipe fitting, put the pipe into the socket of the pipe fitting and wait for crimping.Restate the quality of stainless steel pipe, we promise & ldquo; chromium and nickel & rdquo; Penalty for false and provide quality inspection report and certificate of conformity.Chloride ions exist in the service environment. Chloride ions exist widely, such as salt, sweat, sea water, sea breeze, soil, floating rust of iron foam and so on. Stainless steel corrodes rapidly in the presence of chloride ions, even more than ordinary low carbon steel. Therefore, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry. (in this way, we can give him a & ldquo; improper use & rdquo;) there is an example in the United States: an enterprise uses an oak container to contain a solution containing chloride ions. The container has been used for nearly years. The ninetieth generation of the last century plans to replace it. Because the oak material is not modern enough, the container leaks due to corrosion days after it is replaced with stainless steel.

Model & mdash; The addition of sulfur improves the processability of the material.　　— After that, the second widely used steel is mainly used in food industry and surgical equipment. Molybdenum is added to obtain a special corrosion-resistant structure. Because it has better chloride corrosion resistance than it, it is also made & ldquo; Marine Steel & rdquo; To use. SS is usually used in nuclear fuel recovery units. Grade stainless steel generally meets this application grade. [] Model & mdash; Except that the risk of weld corrosion of the material is reduced due to the addition of titanium, Rockwell and Vickers hardness indexes.Total quality management,Therefore, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry.Section shape stainless steel pipe can be divided into round pipe and special-shaped pipe according to the section shape. Special shaped tubes include rectangular tubes, rhombic tubes, elliptical tubes, hexagonal tubes, tools and mechanical parts. Compared with circular pipe, special-shaped pipe generally has large moment of inertia and section modulus, and has large bending and torsion resistance, which can greatly reduce the structural weight and save steel.When using this process the following key points should be paid attention to: during the welding process, the correct included angle between the welding handle, welding wire and weldment should be maintained. The ideal caster angle of the welding handle nozzle is & deg; & mdash; & deg; and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the included angle between the welding handle and weldment, change the welding speed,JeseniceStainless steel marine pipe, etc. to change the molten pool temperature, so as to ensure Beautiful weld formation (uniform width, no concave, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating so as to facilitate the observation of molten pool and penetration; when filling the welding wire, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding, the welding wire shall be regularly sent and taken out, and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop,Jesenice304dq stainless steel plate, and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.

;- Ferromagnetism due to m transformation shall be considered in use (such as in instrument parts).Total quality management,Add a small amount of sulfur and phosphorus to make it easier to cut.(VI) the growth rate of fixed asset investment in the iron and steel industry dropped significantly. From to June, the investment in fixed assets in the iron and steel industry was . billion yuan, a year-on-year increase of %, of which the investment in ferrous metal smelting and rolling was . billion yuan, a year-on-year increase of %, down percentage point from the same period in ; The investment in ferrous metal mining and dressing was . billion yuan, a year-on-year increase of %, and the growth rate fell sharply by percentage points.Model & mdash; Commonly used precipitation hardening stainless steel model, usually also called -; %Cr,%Ni.Jesenice,Austenitic stainless steel can be used to manufacture stainless spring, clock spring and steel wire rope in aviation structure after deformation strengthening. If welding is required after deformation,Jesenice316 stainless steel chain plate, spot welding process and deformation can only be used to increase the tendency of stress corrosionApplication field: launch the market plan of stainless steel pipe in the target market of new products, such as stainless steel kitchen equipment.Rockwell hardness the Rockwell hardness test of stainless steel pipe is the same as Brinell hardness test. The difference is that it measures the depth of indentation. Rockwell hardness test is widely used at present, and HRC is second only to Brinell hardness Hb in steel pipe standards. Rockwell hardness can be used to measure metal materials from very soft to very hard, which makes up for the disadvantage of Brinell method, It is simpler than Brinell method and can read the hardness value directly from the dial of the hardness machine. However due to its small indentation, the hardness value is not as accurate as Brinell method.