The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.Features of hydraulic lifts: According to the working mode, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations,VannGuide rail chain cargo elevator lifting, docks, airports, hotels, post and telecommunications, municipal gardens garages, cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems, etc. The lift has the advantages of light weight, electric start, simple operation, large working area, especially the ability to cross obstacles for high-altitude operations and the like.Vann,When using a helmet, the helmet should be tightened and worn straight, and the strap of the helmet should be tied under the jaw and tightened.Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.Ndibene Dahra,Regarding the cleanliness of the hydraulic station is there any relevant rule requirement?After the goods are transported, clean up the debris on the platform.What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.

The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.After the elevator enters winter, it is prone to some minor problems and glitches. This requires the user to perform maintenance and maintenance on the elevator in winter. The following editor will briefly introduce the winter maintenance precautions and key points of the elevator.Ensure good power supply at the installation site, install a separate distribution box,VannOutdoor guide rail type cargo elevator, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .Good reputation,Correct construction elevator site inspection First of all,VannWarehouse elevator, we need to check the foundation to see if there is any water accumulation, the lift also has a lot of safety equipment.Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose it can be divided into two types: open type and closed type. Of course, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.

Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.total cost, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.How to install and use tools for elevator bearings During the installation of elevator bearings, it is impossible for us to ensure that the bearings are installed in the right position every time. It is inevitable that some installations will not be in place or the bearings will be offset. The clearance between the bearings becomes too small, and then the inner and outer rings inside the bearing cannot be at the same center of rotation. Therefore, it is necessary to use special tools when installing the bearing, and it is also necessary to use a tester to detect it after the bearing is installed, so that the successful installation of the bearing can be guaranteed.Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .Vann,The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.In addition, it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft, the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.